Fusion
T-Board (updated)
Installation of the Fusion T-Board
1. Remove battery.
2. Remove the screws holding the grip covers.
3. Disconnect battery, eye, and solenoid wires.
4. Remove screws for Stock board
5. Insert Fusion T-board.
6. If needed, insert a washer (included) between the mount and board right by the trigger. (insert if the board does not register trigger pull)
7. Insert screws, connectors, and grip covers.
Functionality
The Fusion T-Board function much like the stock board, however, the setting and
LED functions are different. To turn on the marker, tap the power
button on the back of the grip. As soon as the button is pushed, the LED
will light RED for 0.5 sec, followed by the appropriate LED color for the
mode you are in, you can now release the power button. The marker is now ON and in fire mode. The color of the LED will
denote the mode that the marker is in (see below). To put the marker in
Safety, tap the power button while Live. The LED will flicker
green quickly. To return to Fire state, tap the power button again. When the marker is turned "on", the saved settings are
used. To turn off the marker, depress and hold the power button for 2
sec.
Note1: When you power up your marker for the first time after
installing, the LED may cycles through the colors very
quickly. This loads the default settings, and will only happen on the
first bootup of your Fusion T-Board.
Note2: DIP switch 1 is a 15bps lock. When ON, all modes are restricted to 15bps.
Note3: DIP switch 2 is the Tournament lock. Turn ON for tournament settings.
Shot Q段ng - If enabled, when the
trigger is pulled and no ball is in the breech, the marker will wait up to .25 sec for a ball to enter the
breech and will AUTOMATICALLY fire.
This feature prevents "lost" shots because your fingers are faster
than your hopper, and is still legal on most fields since it does not add shots.
ABS (Anti-Bolt Stick) - If enabled, the first shot will have the ABS dwell
(dwell + ABS setting). All other shots will have the standard dwell. If the marker is not fired for 10 sec, the first
shot will have the ABS setting again.
Force Semi Mode - If the trigger is
pulled and held long enough (Force Semi Time), the marker is
automatically set to semi mode, the eyes disabled, and ROF set to 13bps. This is to
guarantee the marker will function, regardless of the eye or mode.
Note: This feature is disabled on any mode that requires you to
hold the trigger. (NXL, Nitro, Auto)
To disable/enable the eyes - push the
eye button (membrane pad) or setup button on the board until the LED turns RED (disabled, ROF
capped), BLUE (disabled, ROF uncapped) or GREEN (enabled).
When the eyes are disabled, the marker is capped at 13bps, regardless of
MROF setting.
Changing Modes of Fire
1. Turn OFF marker. Hold down trigger and tap the ON button at the
same time. The LED will cycle through its colors very quickly (Disco), let go of
the trigger after the LEDs cycle. You are now in the Modes Menu.
2. Simply press the trigger to cycle through the modes. The color of the
LED indicated which mode you are in...
-Red - NPPL Semi
-Green - Reactive Trigger
-Blue - 3 Round Burst
-White - Full Auto
-Red - CFOA (capped semi)
-Purple - Nitro
-Yellow - PSP Ramping
-Teal - NXL Auto
3. Once you have selected the mode you want, tap the ON
button, the LEDs will cycle again to indicate that your setting has been
saved.
4. The marker has returned to Live Mode with your desired mode of fire.
Adjusting Setting
With your Fusion T-Board, you have full control over how
your marker shoots. Below are the instructions for changing your settings.
This may sound confusing at first, please read the sample below the
chart.
1. Turn Off marker
2.Press and HOLD the EYE button.
3. While holding the EYE button, tap the POWER button
4. Continue to hold the EYE button, the LED will flash red once, pause, then
flash once again. At this time you can let go of the EYE button and you are
now in Setup1 (Reference Chart Below). IF you continue to hold the EYE
button after the first LED blink, and the second LED blink, it will then
blink twice together. If you let go, this will bypass Setup1 and bring you
straight to Setup 2. If you hold the EYE button until the LED blinks 3 times
together and release the EYE button, this will restore the default
settings.
5. Once you are in your desired Setup Menu, the LED color will indicate
which setting you are currently in. Pull the trigger X amount of times to
set your setting. The first pull of the trigger sets the value at its
minimum, each pull after that increments the value based on the chart
below.
6. Tap the EYE button to move on to the next setting. You can also ignore a
setting and bypass to the next setting by not pulling the trigger, and just
tap the EYE button till the LED indicates the setting you desire.
7. When finished with your settings, you can tap the POWER button to enter
Live mode, from any setting or Setup Menu. If you cycle through all the
settings, the marker will automatically exit the menu, and enter live
mode.
8. The LEDs will cycle quickly to indicate your settings were saved.
Setup1 |
Default |
Min |
Max |
Incrmnts |
Color |
ROF* |
15 |
9 |
50 |
1 bps |
Red |
Dwell |
8ms |
4 |
256 |
.5ms |
Green |
Debounce |
5ms |
0 |
256 |
.5ms |
Blue |
Eye Delay |
10ms |
1 |
256 |
.5ms |
Purple |
Force Semi |
2 sec |
0.5 |
none |
.5 sec |
White |
Setup2 |
|
|
|
|
|
Shot Q段ng |
ON |
ON |
OFF |
toggle |
Teal |
ABS |
0ms |
0ms |
256 |
1ms |
Yellow |
After Nitro |
Semi |
n/a |
n/a |
cycle |
Purple |
Trigger speed |
5bps |
5bps |
None |
1bps |
Red |
Trig pulls to ramp |
4 pulls |
2 pulls |
256 |
1 pull |
Blue |
Training |
OFF |
ON |
OFF |
toggle |
Teal |
Training Dwell |
3ms |
1 |
256 |
.5ms |
Green |
Setup3 |
|
|
|
|
|
Restore Default |
n/a |
n/a |
n/a |
n/a |
n/a |
Setup4 |
|
|
|
|
|
Eye Alignment |
n/a |
n/a |
n/a |
n/a |
Red |
Setup1
ROF - Firing speed of the marker
- Min. 9bps -
Dwell - Time Solenoid is on -
Min. 6ms - Increments 1ms
Debounce - Debounce of trigger -
Min. 0ms - Increments 1ms
Eye Delay - Delay after eyes
check to ensure ball is completely in chamber.
Force Semi - Time needed to force
marker into semi mode - Min. 0.5 sec - Increments 0.5 sec.
Setup2
Shot Q段ng - If the trigger is
pulled and no ball is in the breach, the marker will wait for up to シ
sec for a ball to enter the breach and then will AUTOMATICALLY fire.
ABS - On first trigger pull, ABS
is disabled, after that, each trigger pull will increment the ABS 1ms
After Nitro - The LED will blink
Purple followed by the color of the switched mode. Pull the trigger to
cycle the modes.
Trigger Speed - Minumum Trigger
pull speed to activate ramping. I.E. 5bps
Trig pulls to ramp - number of
trigger pulls needed to start ramping.
Training - Allows the marker to be aired up and fired without actually
firing a ball (Provided the Training Dwell is properly set.
Training Dwell - Dwell used for Training. It should only be enough to hear the
marker partially cycle. Should not be able to actually fire a ball.
Setup3 - restores
default factory settings
Example 1: (Remember, the FIRST trigger pull,
resets the setting to the minimum setting. Every trig pull after that
increments)
Tap the POWER button with the Eye Button held down until the LED blinks
once, then once agian. (Setup1), release EYE button.
Pull trigger four times (ROF, 9+1+1+1 = 12 bps), tap EYE button
(next setting),
Tap the EYE button (next setting, Dwell unchanged),
Pull trigger six times (Debounce, 0+1+1+1+1+1 =5ms), tap EYE
button
(next setting),
Tap the EYE button (next setting, Eye Delay unchanged),
Pull trigger three times (Force Semi: .5+.5+.5 = 1.5 s), tap EYE
Button (next setting),
Tap the EYE Button (next setting, Shot Q段ng unchanged),
TAP Power Button (exit Setup mode).
Marker is ready for play with ROF of 12bps, an unchanged Dwell, a 5ms
Debounce, an unchanged Eye Delay, a 1.5s Force Semi, an unchanged Shot Q段ng
setting.
Example 2:
Tap the POWER button with the Eye Button held down until LED blinks twice
quickly (Setup2), release the EYE Button
Click Eye Button (next setting, Shot Q段ng unchanged),
Pull trigger until the LEDs alternate between PURPLE and TEAL (After
Nitro: NXL mode), click Eye Button (next setting),
Pull trigger twice (trigger speed: 5+1, 6bps), click Eye Button (next
setting),
Pull trigger three times (Trig pulls to ramp: 2+1+1+1, 5 pulls),
click Button1 (next setting),
Click the Power button (exit Setup mode).
Marker is ready for play with other settings unchanged, NXL mode
after Nitro, 5bps Trigger speed, and 5 trig pulls to ramp.
Eye Alignment Tool
When in the Eye Alignment Tool, the LED will light up when the eye is
properly aligned. If the eye is blocked or misaligned, the LED will NOT
light. this tool is used to verify that your eyes are clean and
functioning.
|