Send Items to:
Scenario Dreams
PO Box 10874
Burbank, CA 91510-0874
Fax: 818-980-9143 |
|
The
Primal
T-Board User Manual
click
here for printable version
Installation of the T-Board
1. Remove the three screws holding the left handgrip cover
on.
2. Unplug all three connectors located at the top of the
control board. Note which wire goes where.
3. Remove battery.
4. Unscrew the two screws holding the control board in place.
5. Remove the original control board.
6. Insert The T-Board
7. Replace the two mounting screw to secure the T-Board
8. Plug the three connects into the T-Board making sure to
keep the original orientation.
9. If the eyes have been installed, plug the connector into
the receptor located at the bottom of the T-Board.
10. Replace the handgrip cover.
Eyes
If you choose to use the eyes, you MUST replace the stock eyes with
the eyes that come with the T-Board. The stock eyes will not work with
the T-Board and may damage the T-Board if used. Either eye will work in
either hole.
Functionality
The T-Board operates like the stock Spyder control board. When you
pull the trigger, the marker will fire once. Each time the trigger is
pulled, the LED will turn OFF. When the trigger is released, the LED
will turn back on. There is NO burst or full-auto mode on the T-board.
If using the eye, the jumper must be inserted. The eye can be disabled
AT ANY TIME by holding the trigger down for approx two sec. The eye is
disabled when the LED turns on while the trigger is still down. The
Dwell will NOT be changed when disabling the eye. To re-active the eye,
the marker must be turned off for 10 sec. and then turned back on. The
marker MUST be turned off for a minimum for 10 sec. Failure to do so
could cause the marker to not function properly.
The default dwell time is 4ms, default eye delay is 20ms, default
debounce is 4ms, and default eye disable is 2 sec. The minimum dwell
time is 2ms, there is no maximum dwell, the min. debounce is 2ms and min
eye disable is ½ sec. When the marker is turned “on”, the default
dwell time, eye delay, etc. are used. To use a different dwell time or
eye delay, the setup procedure must be used. NOTE: When the marker is
turned off, the T-Board will keep its settings.
To change settings, restore defaults, or enter the Eye Alignment
Tool:
1. Turn marker ON while holding in the trigger.
2. The LED will not light.
3. Continue to hold trigger in.
4. After two sec, the LED will blink once. Release the trigger now
to enter the SETUP mode.
5. After another two sec (four sec total) the LED will blink twice.
Release the trigger now and the T-Board will be restored to its
default settings.
6. After another two sec (six sec total), the LED will turn on. You
are now in the Eye Alignment Tool.
7. Release the trigger.
8. To exit the Eye Alignment Tool, the marker must be turned off for
10 sec.
****IMPORTANT: You MUST restore the defaults
when you FIRST install the T-Board!!!!
SETUP
When you enter the setup mode, the dwell will be set to 2ms, the eye
delay will be set to 0ms, the debounce will be set to 2ms, and the eye
disable will be deactivated. Once you have released the trigger to enter
the setup mode, every pull of the trigger will increment the dwell 1ms
starting at 2ms. When you have set the desired dwell, hold the trigger
down until the LED turns off (approx. 1 sec), now you are in the eye
delay setting mode. Now every pull of the trigger will increase the eye
delay 5ms starting at 0ms. Hold the trigger down until the LED turns off
(approx. 1 sec), now you are in the debounce setting mode. Every pull of
the trigger will increment the debounce 1ms starting at 2ms. Hold the
trigger down until the LED turns off (approx. 1 sec), now you are in the
eye disable setting mode. Every pull of the trigger will increment the
time needed to disable the eye by 500ms (½ sec) starting at 0ms. Hold
the trigger down until the LED turns off (approx. 1 sec), now you are in
play mode. The marker will now operate with your settings.
Example1: Turn on the marker with the trigger held down until the
LED blinks once, release trigger, pull trigger three times, hold
trigger until the LED turns off, release trigger, pull the trigger
four times, hold trigger until the LED turns off, pull trigger
twice, hold trigger until the LED turns off, pull trigger four, hold
trigger until LED turns off. Marker is ready for play with a 5ms
(2+1+1+1) dwell, a 20ms (5+5+5+5) eye delay, a 4ms (2+1+1) debounce,
and 2 sec (½ + ½ + ½ + ½ sec) hold needed to disable the eye.
Example2: Turn on the marker with the trigger held down until the
LED blinks once, release trigger, pull trigger five times, hold
trigger until the LED turns off, release trigger, pull the trigger
twice times, hold trigger until the LED turns off, pull trigger four
times hold trigger until the LED turns off, pull trigger once, hold
trigger until LED turns off. Marker is ready for play with a 7ms
(2+1+1+1) dwell, a 10ms (5+5) eye delay, and a 6ms (2+1+1+1+1)
debounce, and ½ sec hold needed to disable the eye..
Eye Alignment Tool
When in the Eye Alignment Tool, the LED will light up when the eye is
properly aligned. If the eye is blocked or misaligned, the LED will NOT
light.
|
|