Universal
T-Board (Open bolt version)
Installation of the Universal T-Board (One Button, Open Bolt Version)
See install Manual
Functionality
The Universal T_Board function much like a stock board, however, the setting and
LED functions are different. You can use a Button type switch or a slide switch to turn on and change settings.
If you use a slide switch, when the manual says "push and release the button", you would slide the switch on and then off.
To turn on the marker, push and release the button quickly.
The marker is now ON and in fire mode. The color of the LED will
denote the firing mode that the marker is in (see below). To put the marker in
Safety, push and release the button while in Live mode. The LED will flicker
green quickly. To return to firing mode, push and release the button again. When the marker is turned "on", the saved settings are
used. To turn off the marker, push and hold the button for 2
sec.
Note1: When you first connect power to your T-board, it will power up immediately and Disco the LED to load the default settings..
Use the Membrane pad to turn off. Everytime after that the T-board will function as you set it up to.
Note2: DIP switch 1 is the Tournament lock. Turn ON for tournament settings.
Shot Q’ing - If enabled, when the
trigger is pulled and no ball is in the breech, the marker will wait up to .25 sec for a ball to enter the
breech and will AUTOMATICALLY fire.
This feature prevents "lost" shots because your fingers are faster
than your hopper, and is still legal on most fields since it does not add shots.
ABS (Anti-Bolt Stick) - If enabled, the first shot will have the ABS dwell
(dwell + ABS setting). All other shots will have the standard dwell. If the marker is not fired for 10 sec, the first
shot will have the ABS setting again.
Force Semi Mode - If the trigger is
pulled and held long enough (Force Semi Time), the marker is
automatically set to semi mode, the eyes disabled, and ROF set to 13bps. This is to
guarantee the marker will function, regardless of the eye or mode.
Note: This feature is disabled on any mode that requires you to
hold the trigger. (NXL, Nitro, Auto)
To disable/enable the eyes - put the marker in Safe mode and push the
button until the LED turns RED (disabled, ROF
capped), BLUE (disabled, ROF uncapped) or GREEN (enabled) then release the button.
When the eyes are disabled, the marker will be capped at 13bps, unless your in uncapped (Blue).
Changing Modes of Fire
1. Turn OFF marker. Hold down trigger and turn marker ON.
The LED will cycle through its colors very quickly (Disco), let go of
the trigger after the LED cycle. You are now in the Modes Menu.
2. Simply press the trigger to cycle through the modes. The color of the
LED indicated which mode you are in...
-Red - NPPL Semi
-Green - Reactive Trigger
-Blue - 3 Round Burst
-White - Full Auto
-Red - CFOA (capped semi)
-Purple - Nitro
-Yellow - PSP Ramping
-Teal - NXL Auto
3. Once you have selected the mode you want, tap the ON
button on the membrane pad,
the LEDs may cycle again to indicate that your setting has been saved.
4. The marker has returned to Live Mode with your desired mode of fire.
Adjusting Setting
With your Universal T-Board, you have full control over how
your marker shoots. Below are the instructions for changing your settings.
This may sound confusing at first, please read the sample below the
chart.
1. Turn Off marker
2. Press and HOLD the button.
3. Continue to hold the button, the LED will flash red once, pause, then
flash once again. At this time you can let go of the button and you are
now in Setup1 (Reference Chart Below). IF you continue to hold the button after the first LED blink, and the second LED blink, it will then
blink twice together. If you let go, this will bypass Setup1 and bring you
straight to Setup 2. If you hold the button until the LED blinks 3 times
together and release the button, this will restore the default
settings.
5. Once you are in your desired Setup Menu, the LED color will indicate
which setting you are currently in. Pull the trigger X amount of times to
set your setting. The first pull of the trigger sets the value at its
minimum, each pull after that increments the value based on the chart
below.
6. Tap the button to move on to the next setting. You can also ignore a
setting and bypass to the next setting by not pulling the trigger, and just
tap the button till the LED indicates the setting you desire.
7. When finished with your settings, press and hold the button until the LED turns off, this will enter
Live mode, from any setting or Setup Menu. If you cycle through all the
settings, the marker will automatically exit the menu, and enter live
mode.
8. The LEDs will cycle quickly to indicate your settings were saved.
Setup1 |
Default |
Min(ON) |
Max(OFF) |
Incrmnts |
Color |
ROF* |
15 |
9 |
50 |
1 bps |
Red |
Dwell |
7ms |
2 |
256 |
1ms |
Green |
Debounce |
5ms |
0 |
256 |
1ms |
Blue |
Eye Delay |
15ms |
1 |
256 |
1ms |
Purple |
Eye Type |
Break |
Break |
Bounce |
toggle |
Teal |
Force Semi |
2 sec |
0.5 |
none |
.5 sec |
White |
Setup2 |
|
|
|
|
|
Shot Q’ing |
ON |
ON |
OFF |
toggle |
Teal |
ABS |
0ms |
0ms |
256 |
1ms |
Yellow |
After Nitro |
Semi |
n/a |
n/a |
cycle |
Purple |
Trigger speed |
5bps |
5bps |
None |
1bps |
Red |
Trig pulls to ramp |
4 pulls |
2 pulls |
256 |
1 pull |
Blue |
Setup3 |
|
|
|
|
|
Restore Default |
n/a |
n/a |
n/a |
n/a |
n/a |
Setup4 |
|
|
|
|
|
Eye Alignment |
n/a |
n/a |
n/a |
n/a |
Red |
*ROF NOTE: The Eye Delay and Dwell directly affect your Max ROF. If your dwell is very high (stock ION - 34ms) you will
not be able to increase your ROF over 20bps without the board activating its protection mode. This protection mode will
lower your ROF to 7-9bps to prevent damage to your board. you must lower your dwell and eye delay to get higher ROF rates.
Setup1
ROF - Firing speed of the marker
- Min. 9bps -
Dwell - Time Solenoid is on -
Min. 2ms - Increments 1ms
Debounce - Debounce of trigger -
Min. 0ms - Increments 1ms
Eye Delay - Delay after eyes
check to ensure ball is completely in chamber.
Eye Type - Breakbeam or bouncebeam.
Force Semi - Time needed to force
marker into semi mode - Min. 0.5 sec - Increments 0.5 sec.
Setup2
Shot Q’ing - If the trigger is
pulled and no ball is in the breach, the marker will wait for up to ¼
sec for a ball to enter the breach and then will AUTOMATICALLY fire.
ABS - On first trigger pull, ABS
is disabled, after that, each trigger pull will increment the ABS 1ms
After Nitro - The LED will blink
Purple followed by the color of the switched mode. Pull the trigger to
cycle the modes.
Trigger Speed - Minumum Trigger
pull speed to activate ramping. I.E. 5bps
Trig pulls to ramp - number of
trigger pulls needed to start ramping.
Setup3 - restores
default factory settings
Eye Alignment Tool
When in the Eye Alignment Tool, the LED will light up when the eye is
properly aligned. If the eye is blocked or misaligned, the LED will NOT
light. this tool is used to verify that your eyes are clean and
functioning.
TROUBLESHOOTING:
|